|
| RTSS S
| RTSS L
| RTSS SL
|
| Data Upload
|
| mobile data network connection to online cloud storage
| Same as RTSS L
|
| SIM Card
|
| User accessible, any data SIM can be used
| Same as RTSS L
|
| Telemetry Update Rate
|
| Typical update rate to website browser is 5Hz, live data upload to PC software and cloud up to 100Hz depending on connection.
| Same as RTSS L
|
| Memory card
| Removable SD card up to 32GB
|
| Same as RTSS S
|
| Maximum No Channels
| No hard limit, potentially 100s
| Same as RTSS S
| Same as RTSS S
|
|
|
|
|
|
| GPS
| 20Hz update rate. Tracks GPS, GLONASS, BeiDou and Galileo
| Same as RTSS S
| Same as RTSS S
|
| RTK (2cm position)
|
| Optional, requires suitable RTCM correction source
|
|
| GPS Antenna
| 3.3v multi constellation active antenna with SMA connector.
| 3.3v multi constellation active antenna with SMA connector.
| 3.3v multi constellation active antenna with SMA connector.
|
| Mobile data
| The data modem is a globally certified LTE (4G) type with rollback for legacy standards include 3G/2G/GPRS. The modem covers 14 LTE bands (1 2 3 4 5 7 8 12 13 18 19 20 26 28). Whilst that does not guarantee that the system will operate on every network in all countries, it offers excellent performance and the best global coverage of any product of this type we are aware of at this time. For comparison, a current flagship 2024 Iphone covers 17 LTE bands.
Note that the data modem used was updated in late 2023, the previous modem covered 6 LTE bands (1 2 4 5 8 12), so whilst it still offered global coverage, it was more limited with regards which networks it could be used on. In all cases, please check your networks regional LTE band allocations.
|
| Analogue Inputs
| 12 external inputs, 0-25v. All inputs are protected and have a 2nd order filter with corner frequency of 105Hz. Accuracy = 0.4% of measured voltage +-20mV. Sample rate 100Hz.
| 12 external inputs, ratiometric, 0-5v or 0-25v. All inputs are protected and have a 2nd order filter with corner frequency of 105Hz. Accuracy = 0.4% of measured voltage +-20mV. Sample rate 100Hz.
| Same as RTSS L
|
| Frequency Inputs *
| 4 external frequency inputs with a maximum input frequency >2kHz. Triggering voltage requires a low input of <1v and a high input of >4v and 15v maximum.
|
| 4 external frequency inputs with a maximum input frequency >2kHz. Triggering voltage requires a low input of <1v and a high input of >4v and 15v maximum.
|
| RPM *
| 12v frequency input for engine speed.
| Same as RTSS S
| Same as RTSS S
|
| Low side driver
| 4 x low side driver, local firmware controlled, 500mA per channel
| 4 x low side driver, web interface controlled, 500mA per channel
| Same as RTSS L
|
| Power Supply Requirements
| 12v nominal input, minimum of 10v, maximum of 20v. Current consumption TBD
| 12v nominal input, minimum of 10v, maximum of 20v. Current consumption TBD
| 12v nominal input, minimum of 10v, maximum of 20v. Current consumptionTBD
|
| Permanent Supply
|
| External feed to finish uploading data, vehicle or battery pack
| Same as RTSS L
|
| +5v Output 1
| +5v +-1.5% output for powering sensors Maximum current draw 500mA.
| +5v +-0.5% output for powering sensors Maximum current draw 200mA. Voltage source for ratiometric analogue inputs
| +5v +-0.5% output for powering sensors Maximum current draw 200mA. Voltage source for ratiometric analogue inputs
|
| +5v Output 2
| +5v +-1.5% output for powering sensors Maximum current draw 500mA.
|
| +5v +-1.5% output for powering sensors Maximum current draw 500mA.
|
| Case Construction
| Die cast aluminium housing
| Die cast aluminium housing
| Die cast aluminium housing
|
| Connector Type
| 2x 12 way Deutsch DTF, 1x 5 way binder, 1x SMA
| 2x 12 way Deutsch DTF, 1x 5 way binder, 1x6 way binder3x SMA
| Same as RTSS SL
|
| Display connector
| Auxiliary output to enable local monitor of all channels
| Same as RTSS S
| Same as RTSS S
|
| USB port
| Configuration port for setting up unit
| Configuration port, also for downloading locally cached data
| Same as RTSS S
|
| CAN Port 1
| Maximum of 105 individual messages, at up to 1Mbit/s
| Maximum of 60 individual messages, at up to 1Mbit/s
| Same as RTSS S
|
|
| RAW CAN reception
| RAW CAN reception
|
|
| CAN Port 2
| Maximum of 105 individual messages, at up to 1Mbit/s (Optional)
|
| Same as RTSS S
|
|
| RAW CAN reception (Optional)
|
|
|
| Accelerometers
| 3 axis, precision digital output. Guaranteed 2g minimum full scale on all axes. Resolution of 0.005g. Optional 6g sensor available as a factory option.
|
| Same as RTSS S
|
| Vibration
| Factory tested at 25g, 50Hz sinusoid for 5 minutes (without memory card inserted).
| Same as RTSS S
| Same as RTSS S
|
| Temperature
| Factory tested from -20oC to 70oC
| Factory tested from -20oC to 70oC
| Factory tested from -20oC to 70oC
|
| Status indication
| 4 LEDs for Status, GPS, Power, Logging
| 2 line x 16 character status display
| Status LED (Red) and configurable LED (Green)
|
| IP rating
| IP44
| Same as RTSS S
| Same as RTSS S
|
| Mass
| TBD
| TBD
| TBD
|
| Dimensions
| TBD
| TBD
| TBD
|
My basket |
Checkout |
Add to email list
Edit
History
Print
Download (.HTML)
PDF