Something like this?
http://microhydroelectric.ca/store/100A ... ENT-SENSOR
Search found 71 matches
- Mon Jul 25, 2016 11:14 pm
- Forum: Sensor-related questions
- Topic: Sensor recommndation for Amp?
- Replies: 3
- Views: 15631
- Thu Jul 07, 2016 8:00 pm
- Forum: General software support
- Topic: REV Counter not working on dash 2
- Replies: 2
- Views: 11477
- Wed Jun 01, 2016 7:47 pm
- Forum: Sensor-related questions
- Topic: change reading from bar to psi ?
- Replies: 2
- Views: 17560
Re: change reading from bar to psi ?
Should be able to change the formula in the setup page.
I have 2 Dash2 config. files, one displaying gallons of fuel, and one for litres when i'm abroad. Obviously, the sensor is sending the same values, it's only the formula for the display that's different.
I have 2 Dash2 config. files, one displaying gallons of fuel, and one for litres when i'm abroad. Obviously, the sensor is sending the same values, it's only the formula for the display that's different.
- Fri Sep 18, 2015 10:25 pm
- Forum: Sensor-related questions
- Topic: pull up resistor for rt sensor
- Replies: 1
- Views: 11248
- Mon Sep 14, 2015 4:49 pm
- Forum: Sensor-related questions
- Topic: Mk1 Focus Fuel level sender
- Replies: 5
- Views: 48177
- Mon Sep 14, 2015 4:47 pm
- Forum: General support questions
- Topic: VIDEO4 for dummies
- Replies: 3
- Views: 13552
- Fri Sep 04, 2015 6:54 pm
- Forum: General support questions
- Topic: Connecting Dash2 to Computer with v8.5
- Replies: 4
- Views: 12936
- Mon Aug 03, 2015 9:53 pm
- Forum: General support questions
- Topic: Problem connecting PC to Dash2
- Replies: 12
- Views: 22396
- Mon Aug 03, 2015 6:14 pm
- Forum: General support questions
- Topic: Problem connecting PC to Dash2
- Replies: 12
- Views: 22396
- Sun Jul 19, 2015 7:53 pm
- Forum: General support questions
- Topic: GoPro Compatibility
- Replies: 0
- Views: 52702
GoPro Compatibility
Is the Hero 3 White still the most spec'ed GoPro the DL1 Mk3 can sync with?
- Fri May 01, 2015 8:56 pm
- Forum: Sensor-related questions
- Topic: no mph/wheel speed/dash2
- Replies: 2
- Views: 11426
Have you set the source for speed sensor to be "internal" and not "RS232"?
Are you sure your sensor is 5V? The RT sensor needs 12V:
http://www.race-technology.com/wiki/ind ... WheelSpeed
Are you sure your sensor is 5V? The RT sensor needs 12V:
http://www.race-technology.com/wiki/ind ... WheelSpeed
- Wed Apr 29, 2015 9:54 pm
- Forum: Sensor-related questions
- Topic: aem pressure sensor resistance
- Replies: 4
- Views: 13350
- Wed Apr 29, 2015 8:29 pm
- Forum: General support questions
- Topic: Dash2Pro screens
- Replies: 5
- Views: 11949
Re: Dash2Pro screens
BiKenG wrote:what happens when you press the 'Next' button and are already on screen 5?
Cycles to screen 1.
And "Previous" button on screen 1 will cycle to screen 5.
- Wed Apr 29, 2015 8:07 pm
- Forum: Sensor-related questions
- Topic: aem pressure sensor resistance
- Replies: 4
- Views: 13350
http://aemelectronics.com/files/instruc ... 20Data.pdf gives you voltage v pressure.
No resistor needed. Just connect to channel of your choice and use the RT software to setup the sensor from the graph.
Or send me an email to noblem500 (at) gmail.com and i'll reply with info.
No resistor needed. Just connect to channel of your choice and use the RT software to setup the sensor from the graph.
Or send me an email to noblem500 (at) gmail.com and i'll reply with info.
- Sat Apr 18, 2015 12:26 am
- Forum: Sensor-related questions
- Topic: Connecting Dash2/DL1 to ECU Temp Sensors
- Replies: 1
- Views: 9103
Connecting Dash2/DL1 to ECU Temp Sensors
Can i tap into the existing temp sensors that feed into the engine ECU, or will the pull up resistors upset the resistances seen by the ECU?