Search found 19 matches
- Fri Nov 03, 2006 4:15 pm
- Forum: General support questions
- Topic: RPM display not working on DASH1
- Replies: 8
- Views: 16307
- Wed Oct 04, 2006 3:21 pm
- Forum: General support questions
- Topic: Dash 1 condensation
- Replies: 4
- Views: 9609
- Tue Oct 03, 2006 7:59 am
- Forum: General support questions
- Topic: Dash 1 condensation
- Replies: 4
- Views: 9609
Dash 1 condensation
In the lower part of the Dash 1 screen, I seem to have a small amount of condensation. Should this occur? How can I clear it up?
- Thu Aug 24, 2006 10:46 pm
- Forum: General support questions
- Topic: Serious Dash 1 Config problems - URGENT
- Replies: 4
- Views: 9994
- Sun Aug 20, 2006 9:01 pm
- Forum: General support questions
- Topic: Serious Dash 1 Config problems - URGENT
- Replies: 4
- Views: 9994
Serious Dash 1 Config problems - URGENT
Hi guys. I have called and faxed RT for help on this but no response so I thought it worth a shot to post here. At a test day last week my RPM input on the Dash 1 was not working. I am feeding it through the Dl1 from the LT side of the coil. The engine is a 4cyl 2litre pinto. In the DL1 the software...
- Wed Aug 09, 2006 12:11 pm
- Forum: General software support
- Topic: Changing font sizes
- Replies: 2
- Views: 7696
- Tue Aug 08, 2006 8:18 am
- Forum: General software support
- Topic: Changing font sizes
- Replies: 2
- Views: 7696
Changing font sizes
I need to be able to use teh software on a laptop with a 14" screen. As it stands, more 'senior' members of the team can't read anything due to the small font sizes in charts etc. Is there any way to change this? I have searched all the docs but can't find anything.
- Thu Aug 03, 2006 4:13 pm
- Forum: General software support
- Topic: Actual data at a point on the circuit
- Replies: 1
- Views: 6107
Actual data at a point on the circuit
This seems stupid but I am trying to get a readout of the actual data at a point. So I can see at X point I was doing this speed/g/etc. I am sure this is obvious to but other than using the the virtual dash - how do it do it please with the V6 software??
- Wed Jul 12, 2006 12:57 pm
- Forum: General support questions
- Topic: Firmware files for V6.3.62
- Replies: 2
- Views: 7358
- Tue Jun 27, 2006 3:39 pm
- Forum: General support questions
- Topic: 6.3.60 released
- Replies: 2
- Views: 6698
- Tue Jun 27, 2006 7:49 am
- Forum: General support questions
- Topic: Dash 1 + DL1 working well!
- Replies: 0
- Views: 17923
Dash 1 + DL1 working well!
Finally have the Dash 1 and DL1 in the RF82 Van Diemen FF2000. Will post a photo but overall it is working very well. Initial problems in getting a clean RPM signal from the king leand/plug leads but changed to taking a low voltage one off the negative side of the coil and it was instantly very reli...
- Wed Jun 07, 2006 9:14 am
- Forum: Installation questions
- Topic: Replacing Astratech with DL1+Dash1 - Use of old sensors
- Replies: 3
- Views: 10791
Replacing Astratech with DL1+Dash1 - Use of old sensors
I am replacing an old Astratech system with a DL1+Dash 1 Combination. The Astratech has wheel speed, RPM and Throttle position sensors. With the TPS, I was wondering if I should be able to connect it straight into the DL1 rather than replacing it. Not much need I guess for the wheel speed sensor giv...
- Fri May 05, 2006 10:10 am
- Forum: Installation questions
- Topic: Wiring for remote button?
- Replies: 2
- Views: 8594
- Tue Mar 14, 2006 11:11 pm
- Forum: General software support
- Topic: Gear calculation - adjusting for blips
- Replies: 4
- Views: 9656
- Tue Mar 14, 2006 7:33 am
- Forum: General software support
- Topic: Gear calculation - adjusting for blips
- Replies: 4
- Views: 9656
Gear calculation - adjusting for blips
I am trying to get the gear calculation working and other than needing to work out the final drive ratio, my other problem is that it looks like a throttle blip with the clutch depressed can fool the calculation into thinking that a gear change occurred. Not a problem per se as you are downchanging ...