Search found 350 matches

by Support
Thu May 06, 2021 1:14 pm
Forum: General support questions
Topic: Dash2 blank screen
Replies: 2
Views: 228

Re: Dash2 blank screen

Hi, just emailed you regarding this enquiry. If you cannot see it check your junk / spam folder.
by Support
Thu May 06, 2021 1:06 pm
Forum: General support questions
Topic: 8.5 Software and DL1 Mk2 Issue
Replies: 5
Views: 714

Re: 8.5 Software and DL1 Mk2 Issue

The DL1 MK2 can only run on and communicate with V8.5 software / firmware, so if using other products with the DL1 these must also remain on V8.5.
by Support
Wed May 05, 2021 3:08 pm
Forum: General support questions
Topic: Upgrading to DL1 Sport
Replies: 4
Views: 303

Re: Upgrading to DL1 Sport

One of our technical support specialists will study the information you sent and respond to your email.

Regards,
Lorne Winborn
by Support
Wed May 05, 2021 12:37 pm
Forum: Sensor-related questions
Topic: Configuring brake pressure sensor
Replies: 1
Views: 431

Re: Configuring brake pressure sensor

Hello Chris, If you map your input to a pressure channel you will then be presented with a choice of RT-supplied pressure sensors to choose from. In your case select the Bosch brake pressure sensor. The principle is described here: https://www.race-technology.com/wiki/index.php/DL1MK3Configuration/A...
by Support
Wed May 05, 2021 8:49 am
Forum: General support questions
Topic: Upgrading to DL1 Sport
Replies: 4
Views: 303

Re: Upgrading to DL1 Sport

Hello Arno,

Yes it can.

Regards,
Lorne Winborn
by Support
Thu Apr 29, 2021 12:57 pm
Forum: How do I...
Topic: Switching the radiator fan on via Dash2
Replies: 4
Views: 1083

Re: Switching the radiator fan on via Dash2

You have DASH2, not DASH2 PRO, correct?

Which version of DL1 do you have?

Lorne, RT Support
by Support
Fri Apr 09, 2021 3:39 pm
Forum: General support questions
Topic: losing RPM signal sometimes
Replies: 4
Views: 874

Re: losing RPM signal sometimes

Hi Andrew - Yes very conceivable, is the vehicle fuel injected? You could connect the switched negative side of a fuel injector to the RPM low level input ( RL ) and retest. Be aware the DL1 CLUB will need to be configured for the low level input. Open the DL1 CLUB configuration utility > go to the ...
by Support
Tue Mar 23, 2021 4:50 pm
Forum: Sensor-related questions
Topic: Issues getting signal from oil pressure sensor (AIM Motorsport Analouge Sensor)
Replies: 3
Views: 1171

Re: Issues getting signal from oil pressure sensor (AIM Motorsport Analouge Sensor)

No problem Ryan - Unfortunately you won't be able to pick up oil pressure from the OBDII port, you'll need to use a sensor. Oil pressure sensor - https://www.race-technology.com/gb/racing/products/sensors/pressure-sensors/pressure-sensors_oil-fuel-pressure In regards to the DL1, if you are using an ...
by Support
Wed Mar 10, 2021 2:09 pm
Forum: Installation problems
Topic: No RPM on Dash 2 with DL1 Sport
Replies: 3
Views: 2518

Re: No RPM on Dash 2 with DL1 Club

Hi - It sounds like the DL1 CLUB is setup to receive a direct RPM signal from a fuel injector for example and not from the serial port (ECU). The data logger internal RPM must be disabled. Connect the data logger to the laptop > open the DL1 CLUB utility and read the configuration back from the unit...
by Support
Wed Mar 03, 2021 5:28 pm
Forum: Sensor-related questions
Topic: Issues getting signal from oil pressure sensor (AIM Motorsport Analouge Sensor)
Replies: 3
Views: 1171

Re: Issues getting signal from oil pressure sensor (AIM Motorsport Analouge Sensor)

Hi Ryan - Have you checked that the DL1 analogue input is receiving a voltage signal from the sensor?
by Support
Thu Feb 25, 2021 10:45 am
Forum: Installation problems
Topic: Problem with rpm and Dash2!
Replies: 5
Views: 7959

Re: Problem with rpm and Dash2!

Of course Shane - You need to adjust your pulses per rev setting in the dashes configuration. I recommend doubling the current pulses per rev value and retesting. The location of this setting depends on what software you are setting up the dash with. If you email your dash configuration file to dani...
by Support
Wed Feb 24, 2021 3:46 pm
Forum: Installation problems
Topic: Dash 2 firmware
Replies: 7
Views: 12327

Re: Dash 2 firmware

Yes, this issue has been fixed. If you message me on daniel AT race - technology dot com I will send you the new firmware file.
by Support
Fri Feb 19, 2021 4:53 pm
Forum: General support questions
Topic: Solid State Drive
Replies: 2
Views: 1597

Re: Solid State Drive

When you make a DL1 MK2 configuration file, it is up to you to save the file in a suitable location, the software does not automatically store the file in a specific directory. Unfortunately on that model of datalogger it isn't possible to read the settings back form the unit, so really you need to ...
by Support
Mon Feb 15, 2021 5:48 pm
Forum: General support questions
Topic: dash 2 pro canbus set up to life ecu
Replies: 5
Views: 1446

Re: dash 2 pro canbus set up to life ecu

Only via USB connector and DASH2 PRO configuration utility, the Unit Control Inputs section is where you can change the settings.

Best regards
by Support
Mon Feb 15, 2021 5:43 pm
Forum: Pre-sales product questions
Topic: Ecu interface
Replies: 1
Views: 2327

Re: Ecu interface

Hello - Unfortunately not, you will need to disconnect the dash & interface from the ECU.

Best regards

Go to advanced search