Okay,
thank you for the information, I'll have a try and will report if it worked.
Regards.
Patrick
Search found 14 matches
- Wed Mar 21, 2007 8:35 am
- Forum: Sensor-related questions
- Topic: Lap time sensor
- Replies: 9
- Views: 16569
- Mon Mar 19, 2007 11:47 pm
- Forum: Sensor-related questions
- Topic: Lap time sensor
- Replies: 9
- Views: 16569
Hey guys, I've got the same problem. I want to connect a lap beacon onto the DL1 and tested it this morning but it didn't work. Then from a cable I put a 5 Volt signal onto the beacon input that worked well. My lap beacon receiver gives a signal with voltage of 5 Volts and the signal lasts 0,05 seco...
- Fri Mar 16, 2007 10:25 am
- Forum: General support questions
- Topic: Exporting Data
- Replies: 4
- Views: 8833
Hey KenD, a csv file is a comma separated value file. So with a refresh rate of 100 Hz you have 100 lines for one second of logged data. The columns are the different logged channels like time, speed, acceleration (see line 5 of your table) ..... and so on. Data starts in line 6. One line contents t...
- Thu Mar 15, 2007 12:46 pm
- Forum: General support questions
- Topic: Channel allocation for analog inputs in serial output
- Replies: 12
- Views: 20600
- Thu Mar 15, 2007 11:55 am
- Forum: General support questions
- Topic: Channel allocation for analog inputs in serial output
- Replies: 12
- Views: 20600
- Thu Mar 15, 2007 7:20 am
- Forum: General support questions
- Topic: binary format for DL1 serial port
- Replies: 17
- Views: 32476
Hey guys, I'm also very interested in the document and especially the VB script example, because I have to build up a data loggin system for a formula student race car. Please send it to p.ell at rennteam-stuttgart.de Thanks and best regards, Patrick PS: Would be great to have a little download area...
- Wed Mar 07, 2007 9:56 pm
- Forum: General support questions
- Topic: Can anyone tell me what might be happening here?
- Replies: 11
- Views: 17379
- Wed Mar 07, 2007 2:52 pm
- Forum: General software support
- Topic: Accept Serial Input into DL1
- Replies: 8
- Views: 15920
Hey Turby, thanks for your reply. I'm mainly interested in the plugin for the RT software. I want to read in and store the data on the DL1, so that I can later analyze the engine data together with the parameters I log with the DL1 itself. In my opinion to display more than rpm and cooling temperatu...
- Wed Mar 07, 2007 9:01 am
- Forum: General software support
- Topic: Accept Serial Input into DL1
- Replies: 8
- Views: 15920
- Tue Mar 06, 2007 8:14 pm
- Forum: General software support
- Topic: Accept Serial Input into DL1
- Replies: 8
- Views: 15920
- Tue Mar 06, 2007 1:06 am
- Forum: Installation questions
- Topic: Using RPM signal from MoTeC M400 on the DL1
- Replies: 8
- Views: 19611
I connected the tacho output to a oscilloscope but it was'nt a 12V signal. Was quite strange, the signal was below 1 Volt so to low to trigger because for the rpm input you need 5 Volts. I wasn't able to use the rpm signal. But I will try it again on our new Formula Student race car. Best regards, P...
- Tue Mar 06, 2007 12:56 am
- Forum: General software support
- Topic: Accept Serial Input into DL1
- Replies: 8
- Views: 15920
- Mon Mar 05, 2007 2:54 pm
- Forum: General software support
- Topic: Serial Data Output Format
- Replies: 13
- Views: 24908
- Sun Mar 04, 2007 11:08 am
- Forum: General software support
- Topic: Serial Data Output Format
- Replies: 13
- Views: 24908
Serial Data Output Format
Hi! I've got the following problem: In the support area of the Race Technology Homepage there are two pdf files that describe the format of the serial data output. They are linked but unfortunately I cannot download them because you need an account. Where can I get this password account from? Does a...