Page 1 of 1

Dash2Pro an Ecumaster Emu

Posted: Mon Sep 11, 2017 4:15 pm
by mennlein
Hallo
ich versuch grad meine emu an das dash2pro anzuschließen.
leider steht in der ecu liste mein ecumaster emu nicht drin.
kann mir da einer weiter helfen? :?: :?: :roll:

Re: Dash2Pro an Ecumaster Emu

Posted: Sat Sep 16, 2017 8:14 am
by mennlein
Hello
I'm trying to connect the dash2pro to my ecumaster emu. but unfortunately this does not work.
I find my ecu not in the list of the RaceTechnology software v8.5

Re: Dash2Pro an Ecumaster Emu

Posted: Mon Sep 18, 2017 7:18 am
by Support (D)
Dear Sir / Madam,

Which version of the ECUMASTER EMU do you have i.e. 'Black' version with CAN or a serial ECU?

Best regards,
Support(D)

Re: Dash2Pro an Ecumaster Emu

Posted: Tue Sep 19, 2017 6:21 pm
by mennlein
I have serial normal emu . No Black

Re: Dash2Pro an Ecumaster Emu

Posted: Wed Sep 20, 2017 10:37 am
by Support
Hi There,

The ECU master EMU is able to output the Race Technology RS232 data protocol, therefore there is no need to select the ECU from the ECU interface drop down list. Please set this to "Disabled".

Please ensure that you have made the connections required by the ECU as per the below link and also that the Race Technology data protocol has been selected in the ECU mapping software.

http://www.race-technology.com/wiki/ind ... EREMUV1-23

The full list of channels available from this ECU is also available in the above link for your reference.

Kind Regards,
RT Support (SK)

Re: Dash2Pro an Ecumaster Emu

Posted: Wed Dec 27, 2017 11:01 am
by shrek69
Hello
For this option did i need the ECU-licenses?
I have bought a Dash2 pro but i think it was a old unit where all the offered stuff has to buy extra :evil:

Where can i buy the liences?

Regards Bruce

Re: Dash2Pro an Ecumaster Emu

Posted: Wed Jan 03, 2018 9:26 am
by racetec
Hi Bruce

For the ECU Master EMU, no licence is required - this can be set up as described above.
For the 'Black' edition, the CAN Receive option is required - this can be bought from our website here:
https://www.race-technology.com/gb/raci ... /dash2-pro
(Please see 'additional add-ons' at the bottom of the page)

You will need to specify the make and model of the ECU in the 'Special Instructions' at the checkout stage.
I hope this helps.

Best regards,
Adele

Re: Dash2Pro an Ecumaster Emu

Posted: Sat Apr 11, 2020 6:47 am
by Polzi
HI,
with this Post i became my dash working with my EMU Classic. Thank you.
But...
I can not get the Oil Pressure readout, which is one of the most important Datas.
Any tipps for me.
Anything else works, only Oil Pressure not.
In EMU Software i have the data.

Thank you,

Robert

Re: Dash2Pro an Ecumaster Emu

Posted: Tue Apr 14, 2020 8:34 am
by racetec
Hello Robert

Please contact support @ race-technology dot com with details of the issue and one of our technicians will be able to advise you.

Best regards
Support (AH)

Re: Dash2Pro an Ecumaster Emu

Posted: Fri Apr 17, 2020 6:21 am
by Polzi
OK thank you,
email is sent!

Robert