Page 2 of 3
Posted: Thu Jul 17, 2008 4:39 pm
by BBWRacing
Can you let us know what we need to do / get to get this all working together.
Thanks
Leigh
Posted: Fri Aug 15, 2008 2:53 pm
by Jimster
I'm still interested in getting the serial link with the dl1 working with the emerald ecu (not the k3 version)
can this be done?
Cheers
Jim
Posted: Wed Mar 11, 2009 2:24 pm
by BBWRacing
Any news on anyone having this working.
Also can you log the ECU data on the DL1 and view on the software.
Thanks again
Leigh
Posted: Wed Mar 11, 2009 4:28 pm
by Jimster
I was told that Karl at emerald didn't want to spend time on the old m3dk system as it was working with the K3.
I have since replaced my ECU with a K3, but still not got around to buying the interface kit
Posted: Wed Mar 11, 2009 7:11 pm
by BBWRacing
BBWRacing wrote:Any news on anyone having this working.
Also can you log the ECU data on the DL1 and view on the software.
Thanks again
Leigh
Worked out how to set up the ECU varibles on the software, but still cant get the DL1 to log the ECU data or pass the data to the Dash2
Posted: Tue Mar 17, 2009 12:42 pm
by BBWRacing
I've spoken to RT, and it look like you have to plug the ECT interface into the PC lead, not direct to the unit.
Will try tonight and post my findings.
Posted: Wed Mar 18, 2009 12:51 pm
by BBWRacing
BBWRacing wrote:I've spoken to RT, and it look like you have to plug the ECT interface into the PC lead, not direct to the unit.
Will try tonight and post my findings.
Good news its all now working.
Well if you have the DL1 and Dash2 connected to the Emerald via the Emerald PC cable.
The Dash2 is still not working standalone with the Emerald.
Also would have been handy to either put you need to use the Emerald lead in the manual or wire the correct pins in the 9 pin ECU end. (I know if they did this you would not be able to flash update via the PC with out a special converter.)
Posted: Thu Mar 19, 2009 8:07 am
by Jimster
are you using the ECU interface, or going direct from emerald to the DL1?
Is this the K3 or M3dk ECU??
Cheers
Jim
Posted: Tue Mar 31, 2009 2:12 pm
by BBWRacing
Jimster wrote:are you using the ECU interface, or going direct from emerald to the DL1?
Is this the K3 or M3dk ECU??
Cheers
Jim
It's with the RT ECU interface, but you also have to use the PC cable that you get with the EMERALD, unless you convert the RT DB9 connector to use EMERALD pin out not stand serial ones.
Also its the M3dk ECU.
Posted: Wed Feb 17, 2010 11:43 am
by Ragnar
Any news on this? Can the Emerald K3 CAN-communication be used with the Race Technology CAN-adapter? I'm well aware of that there's a serial adapter available, but in this case I'm only interested in CAN.
Posted: Wed Feb 17, 2010 11:46 am
by Jimster
Speaking to Karl at emerald it can be done, I've now got the CAN adapter but not acutally got around to trying it yet.
Posted: Wed Feb 17, 2010 3:52 pm
by Ragnar
Any contact details for Karl?
Posted: Wed Feb 17, 2010 4:03 pm
by Jimster
Tel: 01953 889110...Fax: 01953 889004
emeraldM3D@aol.com
Posted: Tue Mar 23, 2010 9:59 am
by Ragnar
Thought I could leave some feedback. Yesterday I got my Emerald K3 to communicate with my DL1/Dash3-combo through the CAN-interface. Worked very well on the kitchen table
Next step is to implement the installation in the car...
Posted: Tue Mar 23, 2010 11:19 am
by Jimster
could you share what you needed todo to get it working this far?
Cheers
Jim