That one wire Autometer sensor is the only short sensor that I have seen.
Is there anywhere else you use for getting the temp or add some hose/fittings to use the Fragola/tee setup?
Would either of these possibly work?
http://www.ebay.com/itm/1-8-NPT-brass-e ... 3641.l6368
http://www.ebay.com/itm/AEROFLOW-AF372- ... 3641.l6368
Search found 69 matches
- Mon Nov 09, 2015 5:45 pm
- Forum: Sensor-related questions
- Topic: Oil temp and water temp sensors
- Replies: 4
- Views: 23363
- Mon Nov 09, 2015 4:17 pm
- Forum: Sensor-related questions
- Topic: Oil temp and water temp sensors
- Replies: 4
- Views: 23363
Autometer has a short one-wire sensor that will work (p/n 2259), assuming what you are screwing it into is grounded. The calibration curve is readily available with some searching and of course you will need to use a pull up resistor. Otherwise - for things like oil temp, diff temp, etc where you ar...
- Wed Oct 14, 2015 5:27 pm
- Forum: Sensor-related questions
- Topic: Measuring cylinder head tempreture on an air cooled engine
- Replies: 1
- Views: 14792
- Mon Jun 08, 2015 6:35 pm
- Forum: General support questions
- Topic: Dash4 updates
- Replies: 2
- Views: 5798
- Thu Jun 04, 2015 2:55 pm
- Forum: General support questions
- Topic: Dash4 updates
- Replies: 2
- Views: 5798
Dash4 updates
Hello - can this year's updates to the Dash4 be applied to older units or was there a change in hardware?
Thanks.
Thanks.
- Wed Apr 29, 2015 4:18 pm
- Forum: General software support
- Topic: Noisy signals
- Replies: 5
- Views: 23124
- Wed Jan 28, 2015 5:50 pm
- Forum: Sensor-related questions
- Topic: Config Sensors with known characteristics
- Replies: 2
- Views: 10277
- Fri Aug 22, 2014 8:08 pm
- Forum: General support questions
- Topic: DL1 Mk3 - logging internal temp and voltage sensors
- Replies: 1
- Views: 5093
- Tue Aug 19, 2014 5:11 am
- Forum: General support questions
- Topic: Dash4 Pro - Reference Sector Times
- Replies: 0
- Views: 38033
Dash4 Pro - Reference Sector Times
Is this feature available for the Dash 4 (looks like it is available on something, from the link below)? If not, I suppose I need to keep my best lap times on the memory card?
http://www.race-technology.com/wiki/ind ... ectorTimes
Thanks.
http://www.race-technology.com/wiki/ind ... ectorTimes
Thanks.
- Wed Aug 13, 2014 4:38 am
- Forum: General support questions
- Topic: Interpreting sharp loss of calc'd HP
- Replies: 2
- Views: 5809
Well, I thought I had checked out prior data but this calc'd power dropoff seems to be inherent in the calculation as data from years past shows this behavior as well. It seems like the calculation averages a bit of data in front of and behind the given point for which the HP is calculated. I assume...
- Wed Aug 13, 2014 4:23 am
- Forum: General support questions
- Topic: Interpreting sharp loss of calc'd HP
- Replies: 2
- Views: 5809
Interpreting sharp loss of calc'd HP
I am having a tough time reaching what I think my top speed should be and I noticed that calc'd HP is dropping like a brick. I have backed into the CdA based on my known dyno HP level, so I can compare different runs. I believe this drop shows that I have either an engine/tune issue (it is fine on t...
- Tue Aug 12, 2014 1:49 pm
- Forum: General support questions
- Topic: DL1 Mk3/Video 4/Dash4 - Command Failure Timeout
- Replies: 4
- Views: 7988
- Tue Aug 12, 2014 1:15 pm
- Forum: General support questions
- Topic: DL1 Mk3/Video 4/Dash4 - Command Failure Timeout
- Replies: 4
- Views: 7988
- Thu Aug 07, 2014 1:09 am
- Forum: General support questions
- Topic: DL1 Mk3/Video 4/Dash4 - Command Failure Timeout
- Replies: 4
- Views: 7988
DL1 Mk3/Video 4/Dash4 - Command Failure Timeout
Hello. I am trying to get my Mk3, Dash 4 and Video 4 to work together. I can get the Mk3 and Dash 4 to work, but after adding the Video 4, I get a "Command Failure Timeout" error message on the Dash 4. I am not sure what the issue is. The Video 4 has the default data settings for a connect...
- Wed Mar 26, 2014 3:09 pm
- Forum: General support questions
- Topic: User Def variables: error in maths function
- Replies: 8
- Views: 12060