Search found 69 matches
- Tue Jan 10, 2017 1:56 pm
- Forum: General support questions
- Topic: DL1 Not running with SD card installed
- Replies: 8
- Views: 11247
Re: DL1 Not running with SD card installed
Okay, yes in that case I agree, the fault seems to be present in the DL1 MK2. Most likely issue in this case is with the CF card socket. Can you please just check that the pins inside the CF card slot are not bent or touching the other pins in any way. If they seem okay we will have to open the unit...
- Fri Jan 06, 2017 1:54 pm
- Forum: General support questions
- Topic: DL1 Not running with SD card installed
- Replies: 8
- Views: 11247
Re: DL1 Not running with SD card installed
Hi there,
What version of DL1 data logger do you have?
From the information you provided, it sounds like the memory cards are at fault. If possible it would be good if a brand new card, formatted correctly and of correct memory size was used to test this.
Best regards,
Support(D)
What version of DL1 data logger do you have?
From the information you provided, it sounds like the memory cards are at fault. If possible it would be good if a brand new card, formatted correctly and of correct memory size was used to test this.
Best regards,
Support(D)
- Fri Jan 06, 2017 1:46 pm
- Forum: General support questions
- Topic: DL1 Sport / Dash 2 Display live data on PC
- Replies: 7
- Views: 10838
Re: DL1 Sport / Dash 2 Display live data on PC
Hi Bill, You will be able to see the 8 DL1 & 4 DASH2 analogue inputs on the live monitor software at the same time. You require a null modem cable, you might also need a USB to serial adaptor for connecting the null modem to the computer. Look for analogue channels 17 - 20, these will be the ana...
- Wed Dec 21, 2016 11:42 am
- Forum: Installation questions
- Topic: Fuel level pull up resistor.
- Replies: 1
- Views: 32409
Re: Fuel level pull up resistor.
Hello, The pull up resistor is implimented to create a potential divider circuit. This converts the resistance output of the sender to voltage, this is what the DASH2PRO expects to see on its analogue inputs. With a 100ohm resistor attached you should get around 1.875V, firstly I would configure the...
- Fri Dec 02, 2016 9:24 am
- Forum: Sensor-related questions
- Topic: Oil Pressure Readout
- Replies: 2
- Views: 41226
Re: Oil Pressure Readout
Hello,
Would you be able to send me the following:
* Map file from the DTA S40
* Configuration file from the DASH2
* Information on when and where the DASH2 was purchased
Send them to: daniel@race-technology.com
I'll take a look and contact you shortly.
Best regards,
Support(D)
Would you be able to send me the following:
* Map file from the DTA S40
* Configuration file from the DASH2
* Information on when and where the DASH2 was purchased
Send them to: daniel@race-technology.com
I'll take a look and contact you shortly.
Best regards,
Support(D)
- Tue Oct 18, 2016 8:41 am
- Forum: General software support
- Topic: eliminating DASH 3 alarms
- Replies: 1
- Views: 7309
Re: eliminating DASH 3 alarms
Hello Matt,
Have you tried setting the low alarm value lower than 0?
For example set it to: -1000, this should prevent the alarm from triggering.
Kind regards,
Support(D)
Have you tried setting the low alarm value lower than 0?
For example set it to: -1000, this should prevent the alarm from triggering.
Kind regards,
Support(D)
- Tue Oct 04, 2016 9:18 am
- Forum: General software support
- Topic: Track Markers - automatically load?
- Replies: 2
- Views: 8239
Re: Track Markers - automatically load?
Hello Doug, At this point in time that is not a feature implimented into the analysis v8.5 software. For now if you load in a run file you have to load the marker file(s) used at that particular track. I asked one of the directors of RT, he said that sounded like an interesting feature so it could b...
- Tue Sep 20, 2016 8:19 am
- Forum: Sensor-related questions
- Topic: Sensor scaling
- Replies: 4
- Views: 39497
Re: Sensor scaling
Hi, Yes that should be suitable. For the conections on the 5V side, look in the link below for the correct connections. (So instead of using the 5V ref out from the dash you'll be using the 5V ref out from the regulator, the GND from the regulator needs connecting to one of the GND's on the dash.) m...
- Mon Sep 19, 2016 8:20 am
- Forum: Sensor-related questions
- Topic: Sensor scaling
- Replies: 4
- Views: 39497
Re: Sensor scaling
Hello, So based on the readings you've collected from the sender, you can use the 100 ohm resistor however it would be best if you use an external 5V regulator, instead of the DASH2's 5v ref. The DASH2 5V ref is rated for 50mA current draw, connecting this sender to the dash would be get close to th...
- Thu Sep 08, 2016 8:38 am
- Forum: General software support
- Topic: Dash 2 pro Honda Civic type r ep3
- Replies: 4
- Views: 20277
- Thu Sep 08, 2016 8:37 am
- Forum: General software support
- Topic: Dash 2 pro Honda Civic type r ep3
- Replies: 4
- Views: 20277
Re: Dash 2 pro Honda Civic type r ep3
Hello, To fix the rev counter you need to adjust the pulses per revolution, this can be found in the wheel speed and RPM section of the configuration software. As for the static limiter and gear indicator, can you send me the configuration file installed on the dash currently? I'll inspect the confi...
- Fri Sep 02, 2016 2:15 pm
- Forum: General support questions
- Topic: Problem trying to send config to dash
- Replies: 3
- Views: 7900
Re: Problem trying to send config to dash
Hello,
What verion of dash have you got? (DASH2 / DASH2PRO / DASH4PRO etc.)
king regards,
Support(D)
What verion of dash have you got? (DASH2 / DASH2PRO / DASH4PRO etc.)
king regards,
Support(D)
- Thu Aug 18, 2016 3:51 pm
- Forum: General software support
- Topic: aem series 2 with Dash2 pro can issues
- Replies: 1
- Views: 9861
Re: aem series 2 with Dash2 pro can issues
Hello Peter, OK to check exactly what options (licenses) the DASH2PRO has, follow below instructions: Connect the dash to the computer that has RT software installed > read the configuration back from the unit using the DASH2PRO configuration software > go to options > dash options > the options wit...
- Mon Jul 25, 2016 1:54 pm
- Forum: General support questions
- Topic: Monitoring Video4 voltage (is it lower than DL1 voltage ?)
- Replies: 2
- Views: 7020
Re: Monitoring Video4 voltage (is it lower than DL1 voltage ?)
Hi Jimmy, The issue you are seeing is very unlikely to be a lack of voltage issue, if the voltage was too low the unit would completely switch off not just one of the cameras. Have you got any other cameras conencted to the VIDEO4? (If so do they work?) Has the camera (rear SD camera) ever worked co...
- Thu Jul 21, 2016 1:35 pm
- Forum: Sensor-related questions
- Topic: change reading from bar to psi ?
- Replies: 2
- Views: 17531
Re: change reading from bar to psi ?
Hello, Yes this is possible, follow the instructions below: Open the DASH2 config software > load in the current config file installed on the dash > use the drop down box at the top of the input scaling tab to select the analogue input you have the sensor connected to (i.e. DASH2 Analogue 1 - DASH2 ...