Search found 362 matches
- Thu Oct 04, 2018 11:09 am
- Forum: Installation problems
- Topic: Dash 2 sensors set up
- Replies: 4
- Views: 15272
Re: Dash 2 sensors set up
Hello, You have a few options in this situation. 1) Use one of our ECU interfaces / CAN adaptors to obtain the data from the ECU & display it on the dash. However check if your model of DTA ECU is on our list of compatible aftermarket ECUs first - http://www.race-technology.com/gb/racing/products/e...
- Wed Oct 03, 2018 3:08 pm
- Forum: General support questions
- Topic: Live Monitor showing incorrect analogue voltage readings
- Replies: 1
- Views: 5871
Re: Live Monitor showing incorrect analogue voltage readings
Hello,
Can you send us your DL1 & DASH2 configuration files to my email: daniel (at) race - technology (dot) com for inspection? Additionally, some test data would be most useful in this situation.
Support (D)
Can you send us your DL1 & DASH2 configuration files to my email: daniel (at) race - technology (dot) com for inspection? Additionally, some test data would be most useful in this situation.
Support (D)
- Wed Oct 03, 2018 3:02 pm
- Forum: General support questions
- Topic: Approach for tracks where start line and finish line are not in the same place
- Replies: 2
- Views: 117626
Re: Approach for tracks where start line and finish line are not in the same place
Hello,
in this situation there are two options:
1) Drop the lap marker where the finish line is going to be on the circuit.
2) Use the analysis tool to drop "start of run" & "end of run" markers onto the circuit.
Support (D)
in this situation there are two options:
1) Drop the lap marker where the finish line is going to be on the circuit.
2) Use the analysis tool to drop "start of run" & "end of run" markers onto the circuit.
Support (D)
- Wed Oct 03, 2018 2:52 pm
- Forum: General support questions
- Topic: DL1 running 2 x displays ?
- Replies: 1
- Views: 5590
Re: DL1 running 2 x displays ?
Hello,
Check this out - http://www.race-technology.com/gb/racin ... tter-cable.
Support (D)
Check this out - http://www.race-technology.com/gb/racin ... tter-cable.
Support (D)
- Wed Oct 03, 2018 1:30 pm
- Forum: General support questions
- Topic: Dash2 Fuel Level Clip at 0 and 100?
- Replies: 1
- Views: 5685
Re: Dash2 Fuel Level Clip at 0 and 100?
Hello,
Please send your DASH2 configuration file & voltage versus fuel level readings to my email: daniel (at) race - technology (dot) com for inspection.
Support (D)
Please send your DASH2 configuration file & voltage versus fuel level readings to my email: daniel (at) race - technology (dot) com for inspection.
Support (D)
- Wed Oct 03, 2018 12:25 pm
- Forum: Installation problems
- Topic: system fail to communicate send configuration ERROR
- Replies: 1
- Views: 6267
Re: system fail to communicate send configuration ERROR
Dear Customer, Try connecting the DASH2 directly to the computer if you haven't already i.e. black D-type communications connector from the dashes wiring harness > USB to serial adaptor > computer USB port. If that doesn't work check the firmware version your DASH2 is running on i.e. press & hold t...
- Mon Sep 17, 2018 11:04 am
- Forum: General support questions
- Topic: Revs higher than 9000rpm and fuel sending question - motorbike related
- Replies: 5
- Views: 7092
Re: Revs higher than 9000rpm and fuel sending question - motorbike related
Hello,
Yes it is possible to increase the odometer reading. Please email sales @ race - technology . com for a quote.
Kind regards,
Support (K)
Yes it is possible to increase the odometer reading. Please email sales @ race - technology . com for a quote.
Kind regards,
Support (K)
- Mon Sep 17, 2018 10:50 am
- Forum: General support questions
- Topic: Revs higher than 9000rpm and fuel sending question - motorbike related
- Replies: 5
- Views: 7092
Re: Revs higher than 9000rpm and fuel sending question - motorbike related
Hello, 1) No. You can entre any value between 0-19. The advisory message means each box must have a bigger value then the previous. For example 0 1 2 3 4 3 2 1 0 would not work. I am not sure why we needed to state that. ;-) http://i68.tinypic.com/1042007.jpg 2) Connect sensor like below. Resistor a...
- Thu Aug 30, 2018 8:46 am
- Forum: Pre-sales product questions
- Topic: Dash2 Italiano
- Replies: 18
- Views: 17849
Re: Dash2 Italiano
Hello, Here are some useful links to the knowledge base regarding lap timing. https://www.race-technology.com/wiki/index.php/LapTiming-NEW/LapTimingOperation https://www.race-technology.com/wiki/index.php/DASH2-NEW/LapTiming-NEW If you are running the new DASH2 firmware the configuration is set up u...
- Tue Aug 28, 2018 2:18 pm
- Forum: General support questions
- Topic: DL1 MK1 No Longer Recording on CF Card
- Replies: 13
- Views: 13351
Re: DL1 MK1 No Longer Recording on CF Card
Hello, I can confirm Windows has stopped supporting the FAT16 filing system in Windows 10. You are also unable to refomat a memory card using the Race Technology software as the software only calls the Windows routine to format the card. I recommend buying a few cards and not reformatting them routi...
- Fri Jul 27, 2018 1:54 pm
- Forum: General support questions
- Topic: Boost Display/Logging - Dash 4 pro - DL1 Club, SC Typhoon ECU
- Replies: 1
- Views: 5577
Re: Boost Display/Logging - Dash 4 pro - DL1 Club, SC Typhoon ECU
Hello,
If you can email me the following I'll be able to assist:
- A copy of your DL1 CLUB configuration.
- A copy of your DASH4PRO configuration.
- A small .RUN file (around ten seconds): logged with the engine running & a 'few' blips of the throttle present.
Best regards,
Tech Support (D)
If you can email me the following I'll be able to assist:
- A copy of your DL1 CLUB configuration.
- A copy of your DASH4PRO configuration.
- A small .RUN file (around ten seconds): logged with the engine running & a 'few' blips of the throttle present.
Best regards,
Tech Support (D)
- Fri Jul 27, 2018 1:39 pm
- Forum: General support questions
- Topic: DL1/Dash2 Does not start logging
- Replies: 10
- Views: 11743
Re: DL1/Dash2 Does not start logging
Check your "Pulses per revolution" setting on your DASH2 configuration. Alternatively, send a copy of your DASH2 configuration to: daniel at race - technology dot com.
Best regards,
Tech Support (D)
Best regards,
Tech Support (D)
- Fri Jul 27, 2018 12:59 pm
- Forum: Sensor-related questions
- Topic: Terratrip Wheel Speed Sensor
- Replies: 1
- Views: 6330
Re: Terratrip Wheel Speed Sensor
Hello,
If you're struggling to obtain a valid speed signal from the Terratrip sensor, here is the one we sell - https://www.race-technology.com/gb/raci ... heel-speed.
Best regards,
Tech Support (D)
If you're struggling to obtain a valid speed signal from the Terratrip sensor, here is the one we sell - https://www.race-technology.com/gb/raci ... heel-speed.
Best regards,
Tech Support (D)
- Thu Jul 26, 2018 7:38 am
- Forum: Pre-sales product questions
- Topic: Megasquirt MS3 and 2 way CAN
- Replies: 1
- Views: 6527
Re: Megasquirt MS3 and 2 way CAN
Dear Andy, To receive CAN data from the Megasquirt MS3 CAN ECU, you will require the following: - DL1 CLUB - this will come with the correct firmware pre-installed. - DL1 CLUB CAN Reveive Option License - this will come with our CAN interface cable. Both of these can be purchased here - http://www....
- Thu Jun 21, 2018 1:41 pm
- Forum: How do I...
- Topic: Test Dash4Pro
- Replies: 17
- Views: 15455
Re: Test Dash4Pro
Hello, I don't understand why the DASH4 will not work using the latest firmware. The format of the data has stayed the same. This makes no sense... I've spoken to Life, and they say the best route is to have the F88 ECU reconfigured to send CAN over RS232 You can send data over CAN or RS232 it is th...
