Search found 366 matches

by Support
Thu Jun 25, 2020 8:41 am
Forum: General support questions
Topic: Connecting Dash2 to Computer with v8.5
Replies: 4
Views: 5335

Re: Connecting Dash2 to Computer with v8.5

Hi zub, You are able to read the configuration back from the DASH2 if the firmware is version 10.0.0 or later . To find out which version of firmware is running on your DASH2, you need to: Press and hold the DOWN button, power up the unit keeping the button pressed and wait for the firmware version ...
by Support
Wed Jun 24, 2020 11:38 am
Forum: Installation problems
Topic: Connecting D2P to Rover Mems ECU
Replies: 6
Views: 1472

Re: Connecting D2P to Rover Mems ECU

Hello Keith - Dan here, it seems you didn't receive my last email I'll post it below so you can read it: Apologies for the delay, I had to stay off work after a COVID-19 test. I can see a couple of problems: 1) The Terminator lead should not be connected to Serial Port 2 i.e. RS232 (2) . This should...
by Support
Wed Jun 10, 2020 11:53 am
Forum: General support questions
Topic: Corner radius
Replies: 3
Views: 855

Re: Corner radius

Hello,

Corner radius is automatically calculated in both V8.5 and V10. You may just need to enable in variable manager.

Please see below...

Image

Image
by Support
Thu May 21, 2020 10:57 am
Forum: How do I...
Topic: ...overlay sprint/hillclimb runs in 8.5
Replies: 5
Views: 1442

Re: ...overlay sprint/hillclimb runs in 8.5

Hello,

Have you tried using the selection scratchpad? - http://www.race-technology.com/wiki/ind ... Scratchpad

Support (K)
by Support
Thu Apr 23, 2020 3:19 pm
Forum: Sensor-related questions
Topic: oil pressure sensor checks
Replies: 5
Views: 3672

Re: oil pressure sensor checks

Hello Anthony, If you have a question, why not email me directly like you have done many times in past, every one of which I have responded to? I'm sorry if this has somehow fallen short of your expectations. Temperature sensors have a potential divider resistor. The pressure sensors we supply do no...
by Support
Fri Mar 22, 2019 11:02 am
Forum: General support questions
Topic: GPS ROLLOVER
Replies: 5
Views: 4318

Re: GPS ROLLOVER

If there is an issue you can rest assured that it will be easily fixed with a firmware update for your DL1. We are looking into this now and will shortly inform you further.

Support (LW)
by Support
Thu Dec 13, 2018 10:08 am
Forum: How do I...
Topic: How to show min/max value in a sector, Dash4Pro
Replies: 5
Views: 11601

Re: How to show min/max value in a sector, Dash4Pro

Hello, Using min/max in a formula allow you to see the min or max or a set of variables. For example... MAX(EGT1,EGT2,EGT3,EGT4) will display the hottest of the 4 EGT's. On the DASH4 it is possible to do it by using x in a user defined variable as the previous value. For example... If(EGT1>x,EGT1,x)...
by Support
Fri Oct 19, 2018 8:35 am
Forum: Installation questions
Topic: Dash 2 Pro fuse
Replies: 5
Views: 8438

Re: Dash 2 Pro fuse

Excellent thanks for the information, it seems the correct fuse rating has been used for your installation, this means there shouldn't be any internal damage caused to your DASH2PRO. From your first post it appears the issue is located within the CONN B connector itself or the connected wiring. Thi...
by Support
Thu Oct 18, 2018 2:54 pm
Forum: Installation questions
Topic: Dash 2 Pro fuse
Replies: 5
Views: 8438

Re: Dash 2 Pro fuse

Hello,

Can you firstly tell us the fuse rating(s) & if there is any other equipment connected to the DASH2PRO please? Thanks

Support(D)
by Support
Wed Oct 17, 2018 2:46 pm
Forum: General support questions
Topic: DL1 MK1 & DASH3LITE firmware - Shift Light Issue
Replies: 1
Views: 6290

Re: DL1 MK1 & DASH3LITE firmware - Shift Light Issue

Hello,

If you email us directly at: daniel (at) race - technology (dot) com, we'll be able to send you the latest firmware file for the DL1 MK1.

Support(D)
by Support
Wed Oct 17, 2018 2:43 pm
Forum: Pre-sales product questions
Topic: engine system malfunction indicator and warning light.
Replies: 3
Views: 15170

Re: engine system malfunction indicator and warning light.

Yes but only if the following points are true: You're sure the ECU malfunction wire has a varying voltage, with the range you've specified in your last post. The dash will give you an on-screen alarm provided it has been properly configured to do this. You'll need to connect the sensor GND ( Red & ...
by Support
Mon Oct 08, 2018 12:36 pm
Forum: Installation questions
Topic: requirement for diodes in circuits.
Replies: 1
Views: 6315

Re: requirement for diodes in circuits.

Hello, The DASH2PRO has built in protection diodes, so there is no requirement to fit any on the dashes wiring. However we do expect the customer to fit the supplied fuse (0.5A / 500mA) into the dashes wiring. If unsure we offer a fitting service or you may want to consult a qualified electronics t...
by Support
Mon Oct 08, 2018 12:31 pm
Forum: Pre-sales product questions
Topic: engine system malfunction indicator and warning light.
Replies: 3
Views: 15170

Re: engine system malfunction indicator and warning light.

Hello, The DASH2PRO doesn't boast a designated "Engine Malfunction" warning LED as such. However you can connect the ECUs engine malfunction signal wire to one of the dashes analogue inputs (provided it does in fact have a varying voltage). From this you can create an alarm to appear on the dash wh...
by Support
Mon Oct 08, 2018 12:10 pm
Forum: Installation problems
Topic: MBE 9A4 to Dash2pro CAN profile
Replies: 1
Views: 6371

Re: MBE 9A4 to Dash2pro CAN profile

Hello, When a customer purchases a CAN receive license for a DASH2PRO, we send them a .CAN file & installation instructions via email. The .CAN file includes all of the CAN information the customer requires i.e. CAN IDs, CAN ID length, CAN baud rate, byte ordering, scale, offset etc. The customer t...
by Support
Fri Oct 05, 2018 2:05 pm
Forum: How do I...
Topic: "Speed and distance options" for Dash 4 Pro
Replies: 3
Views: 7029

Re: "Speed and distance options" for Dash 4 Pro

Hello Charles, These options are only relevant when our DASH4PRO is connected to our SPEEDBOX product. They have no affect when using the DASH4PRO with our DL1 / RT LIVE data loggers. Additionally, if the second speed option is selected "processed speed" is used instead of "GPS speed" when availabl...

Go to advanced search