Search found 9 matches

by Joao Basso
Wed Dec 13, 2017 12:30 pm
Forum: General software support
Topic: Sending VD4 to Youtube
Replies: 2
Views: 9155

Re: Sending VD4 to Youtube

Hello,

Worked perfectly, thank you!
I already had the overlay added and it had some things not so well done... nothing I can do now, I guess.
It is better to add overlays after, when converting the videos, for sure.
by Joao Basso
Mon Dec 11, 2017 2:57 pm
Forum: General software support
Topic: Sending VD4 to Youtube
Replies: 2
Views: 9155

Sending VD4 to Youtube

It should be easy but the VD4 files are refused by Youtube.
I tried virtual dub but it requires codecs that I have no ideia how to get and/or install...

Is there a simple stupid-proof way of sending the VD4 to youtube?

Thanks

Joao
by Joao Basso
Mon Dec 11, 2017 2:50 pm
Forum: General software support
Topic: CAN wheel speed and gear dificulties
Replies: 4
Views: 13785

Re: CAN wheel speed and gear dificulties

Hello,

Problem sorted. It was not VAR_1500 but it was just a typing error from me. I reviewed it several times so if it passed by, I must be getting old!

Thanks for the Gear solution.

Kind regards

Joao Basso
by Joao Basso
Wed Nov 29, 2017 2:30 pm
Forum: General software support
Topic: CAN wheel speed and gear dificulties
Replies: 4
Views: 13785

Re: CAN wheel speed and gear dificulties

Hello, I still have the problem with the FL wheel speed. It reads zero when all the other read the real speed. Can be many things I know but can it be to many CAN channels? Any sugestions? The speed for the gear calculation is comming from the GPS. Can I change that and have the wheel speed controli...
by Joao Basso
Wed Nov 08, 2017 12:25 pm
Forum: General software support
Topic: CAN wheel speed and gear dificulties
Replies: 4
Views: 13785

CAN wheel speed and gear dificulties

Hello, My system is configured to read 4 wheel speeds from the 4 wheels in this BMW 1 series. Those 4 wheel speeds are assigned (on the CAN config tool) to 4 frequency channels (freq 25 to 29). 3 of those 4 channels are readable in my Dash3 but the the FL wheel (Freq 25) always reads zero. I believe...
by Joao Basso
Tue Oct 31, 2017 9:24 am
Forum: General software support
Topic: Lite Monitor working - Monitor not working
Replies: 4
Views: 16442

Re: Lite Monitor working - Monitor not working

Hello, RPM working fine after following your advice. Thank you! Now I have another problem: speed value to have the gear calculation working. Previously I was reading speed and RPM from the OBD and the gear calculation worked fine. Now I only read speed from wheels and the gear takes some time to wo...
by Joao Basso
Tue Oct 24, 2017 10:32 am
Forum: General software support
Topic: Lite Monitor working - Monitor not working
Replies: 4
Views: 16442

Re: Lite Monitor working - Monitor not working

Many thanks for your reply. Understood your tip. I will try it when I have the time. There is an info that I did not say: before I was using the OBD2 option to collect the RPM and I have RPM reading in the Dash3 but I believe I was using another RPM channel and not Engine Speed (ECU). Does this make...
by Joao Basso
Mon Oct 23, 2017 5:24 pm
Forum: General support questions
Topic: Incorrect value in Dash 3?
Replies: 1
Views: 12980

Re: Incorrect value in Dash 3?

Hi André,

When configuring the DASH3, you can apply a multiplicative factor to any channel. Have you checked that?

João
by Joao Basso
Mon Oct 23, 2017 5:15 pm
Forum: General software support
Topic: Lite Monitor working - Monitor not working
Replies: 4
Views: 16442

Re: Lite Monitor working - Monitor not working

Hello, This is an old topic but I'm facing the same issue with my DL1 + DASH3 + CAN interface. The CAN interface is set to read 14 channels including the engine speed from my BMW and it reads them perfectly in the Lite Monitor. For the RPM, the channel I'm using in the CAN interface is "Engine ...

Go to advanced search