Search found 17 matches

by Capposteve
Sat Nov 10, 2012 11:23 am
Forum: General support questions
Topic: lcd going dim
Replies: 1
Views: 3835

lcd going dim

hey. well had this dash 2 for abut 3-4 months now and since then iv never really done much night time driving. well i did a 40 minute drive the other night and noticed that after about 20 minutes with the back light on it fades off to it being so dim you can hardly see anything. if you turn it off a...
by Capposteve
Sun Sep 23, 2012 10:26 am
Forum: General software support
Topic: speed disapears after 80 odd mph
Replies: 4
Views: 10147

its going into the actual speed input on the dash 2
by Capposteve
Sat Sep 22, 2012 10:50 pm
Forum: General software support
Topic: speed disapears after 80 odd mph
Replies: 4
Views: 10147

speed disapears after 80 odd mph

as the title says, i have a dash 2 and works faultlessly. now when i go anywhere above 80-85 mph the mph readout goes to 0mph. i know i have a speed cut at 86mph from my ecu and im taking the speed signal strait from where it was plugged into the original cliocks. i also no that the speed cut doesnt...
by Capposteve
Thu Sep 20, 2012 6:30 pm
Forum: Sensor-related questions
Topic: pull up resistor formula
Replies: 18
Views: 31841

I need it to change as slow as possible as I don't have any baffles in the tank at the mo

Thanks.
by Capposteve
Wed Sep 19, 2012 4:41 pm
Forum: Sensor-related questions
Topic: pull up resistor formula
Replies: 18
Views: 31841

What is the best setup for max filtering?? Thanks
by Capposteve
Wed Jul 18, 2012 4:55 pm
Forum: Sensor-related questions
Topic: pull up resistor formula
Replies: 18
Views: 31841

Thanks for clearing that up. I Spose also it depends on how the filtering is set up on the dash2 as well.
by Capposteve
Wed Jul 18, 2012 7:19 am
Forum: Sensor-related questions
Topic: pull up resistor formula
Replies: 18
Views: 31841

What's that Martin?? The dash2 5v or my 9v power supply?

Steve
by Capposteve
Wed Jul 18, 2012 7:14 am
Forum: Sensor-related questions
Topic: pull up resistor formula
Replies: 18
Views: 31841

Thanks for the replys. Although the regulated supply is ragulated to 98% 9v. As far as the filtering it has a few capacitors and resistors built onto the board So I'm hoping it wi be ok. Iv only decided to do it this way as iv heard of many doing it before. Plus I don't have a dl-1 and the 50mah 5v ...
by Capposteve
Tue Jul 17, 2012 11:38 am
Forum: Sensor-related questions
Topic: pull up resistor formula
Replies: 18
Views: 31841

Actualy I have just decided to run it with a 9v regulated supply and I'm getting about a 3-4v swing with a 220r resistor. Is that enough swing?? Cheers.
by Capposteve
Mon Jul 16, 2012 10:22 am
Forum: Sensor-related questions
Topic: pull up resistor formula
Replies: 18
Views: 31841

Hi that's perfect thanks. What size pull up would I need for a decent voltage swing as iv ordered a 2amp regulated 5v supply.

Thanks.
Steve
by Capposteve
Mon Jul 16, 2012 6:40 am
Forum: Sensor-related questions
Topic: pull up resistor formula
Replies: 18
Views: 31841

Hi. Thanks for that. Iv seen this already and orders two 220r resistors as my fuel sender is 0-130 ohm and my temp is 0-178 ohms. I take it the higher the resistance resistor you use the less voltage swing you get but also less current draw and visa versa. Thanks steve
by Capposteve
Sun Jul 15, 2012 8:28 pm
Forum: Sensor-related questions
Topic: pull up resistor formula
Replies: 18
Views: 31841

pull up resistor formula

hi, iv been scratching my head all night trying to work this out and was wondering if there was a table or furmula somewhere that can help me work out what wattidge resistor i need for a couple sensors. how are we ment to be able to tell what resistor and what our final voltage range will be. many t...
by Capposteve
Thu Jul 12, 2012 7:43 pm
Forum: General software support
Topic: Dash2 shift light not working
Replies: 5
Views: 18139

Thanks very much for clearing that up. I have the status turned on but don't need it on as I have no dl1. Cheers.
by Capposteve
Thu Jul 12, 2012 4:59 pm
Forum: General software support
Topic: Dash2 shift light not working
Replies: 5
Views: 18139

Hi. Thanks. Where in the menu can u sellect the led used?? I notice. The far right two res LEDs light when in alarm but thats about it
by Capposteve
Tue Jul 10, 2012 7:54 pm
Forum: General software support
Topic: Dash2 shift light not working
Replies: 5
Views: 18139

Dash2 shift light not working

Hey. Just received my brand new dash 2 and whilst setting up shift light brightness I noticed the far left led does not light up. Is this normal during the brightness setup??

Steve

Go to advanced search