Search found 21 matches

by sparkystav
Tue Feb 23, 2021 5:41 pm
Forum: General software support
Topic: Dash 2 firmware
Replies: 7
Views: 26129

Re: Dash 2 firmware

Did this firmware issue with older Dash2 and v10 ever get fixed?
by sparkystav
Sun Nov 05, 2017 10:36 pm
Forum: General software support
Topic: Dash 2 firmware
Replies: 7
Views: 26129

Re: Dash 2 firmware

I had the same issue.

Firmware 10 for the Dash2 didn’t work with pressure sensors from my Ecu.
Went back to 9.3.5 and it works.

You’ll find the older firmware in the “flash” folder in the c: program files folder for the race technology software.
by sparkystav
Sun Oct 22, 2017 9:49 pm
Forum: General software support
Topic: Link G4+ and Dash2
Replies: 3
Views: 11215

Re: Link G4+ and Dash2

Have just emailed thanks. Didn’t get a reply notification so sorry for the delay
by sparkystav
Fri Sep 22, 2017 9:34 pm
Forum: General software support
Topic: Link G4+ and Dash2
Replies: 3
Views: 11215

Re: Link G4+ and Dash2

Right I’ve got the two units talking.

But can I set the Dash2 (not pro!) to read custom CAN data? For example the lambda signal isn’t on the pre set Vipec/link drop down.
by sparkystav
Fri Sep 22, 2017 4:33 pm
Forum: General software support
Topic: Link G4+ and Dash2
Replies: 3
Views: 11215

Link G4+ and Dash2

Does anyone have a config file for a Link to Dash2 (not pro) via CAN please?

Would save me putting them all in.

Thanks!
by sparkystav
Mon May 08, 2017 10:29 pm
Forum: General software support
Topic: Dash2 and Link G4+ interface
Replies: 4
Views: 9862

Re: Dash2 and Link G4+ interface

No problem, it's still a cheaper option than buying a new Dash2 pro if I can do it with CAN on my Dash2.

Thanks
by sparkystav
Mon May 08, 2017 9:30 am
Forum: General software support
Topic: Dash2 and Link G4+ interface
Replies: 4
Views: 9862

Re: Dash2 and Link G4+ interface

Thank you for the reply. I will get in touch with Link about the possible changed serial protocols.

Can the older dash 2 (i.e. The one I have) connect via can? Could I rewire the connection to use that instead with the Ecu interface I have?

Marc
by sparkystav
Sat May 06, 2017 7:59 am
Forum: General software support
Topic: Dash2 and Link G4+ interface
Replies: 4
Views: 9862

Dash2 and Link G4+ interface

I have an older Dash2 with the Serial Ecu interface (I originally bought this for my old Link G4 storm) I have now upgraded to the Link G4+ Fury, however I can't get any of the AN Volt signals to appear on the dash2 I've followed the guide and setup he Dash2 using the Aux14 onwards as the AN Volt ch...
by sparkystav
Sun Apr 05, 2015 5:31 am
Forum: Installation questions
Topic: Dash2 input buttons
Replies: 6
Views: 19929

pretty much yes, but it hides the inputs to the dash to a location that doesnt look out of place.

I like to do things a little differently
by sparkystav
Fri Apr 03, 2015 2:56 am
Forum: Installation questions
Topic: Dash2 input buttons
Replies: 6
Views: 19929

Thanks, but i understand that,

im basically wondering if having the signal move to 5v when not grounded would damage the board?
by sparkystav
Mon Mar 30, 2015 9:34 am
Forum: Installation questions
Topic: Dash2 input buttons
Replies: 6
Views: 19929

No one?
by sparkystav
Mon Mar 23, 2015 4:24 am
Forum: Installation questions
Topic: Dash2 input buttons
Replies: 6
Views: 19929

Dash2 input buttons

Hello, having installed my Dash 2 im not keen on having 4 buttons on the dash so im looking at a system using an Arduino chip that converts programmed specific resistance readings into digital outputs. Basically im using a 4 cruise control lever to simulate the 4 buttons. Each way on the lever gives...
by sparkystav
Mon Apr 30, 2012 6:10 pm
Forum: Installation questions
Topic: Dash2 with Link g4 - only showing 2 readings?
Replies: 1
Views: 6385

Right a bit more research and i seem to have solved both in one!

using the diagram in this thread:

http://www.race-technology.com/forum/vi ... 2&start=15

I had the Rx to Rx and Tx to Tx when the should be opposing. Doh!

switched them round and voila, dash now reads ecu and the third input now appears!

hope this helps someone else.
by sparkystav
Mon Apr 30, 2012 4:51 pm
Forum: Installation questions
Topic: Dash2 with Link g4 - only showing 2 readings?
Replies: 1
Views: 6385

Dash2 with Link g4 - only showing 2 readings?

Hello, i have a dash 2 and ive installed it in my Lexus with a Link G4. I have 2 problems though: 1- the dash2 only shows 2 readings - the large one on the right, and the middle one. I cant get the left hand reading to appear?! 2- Talking to the link g4 seems not to want to happen. Ive connect the d...
by sparkystav
Sun Nov 20, 2011 9:23 pm
Forum: General support questions
Topic: DL1 + Dash2 + LINK/Vipec = looses RPM every now and then.
Replies: 3
Views: 6583

Hi mate,

sorry cant help with your problem, but im currently installing a dash2 with a link G4 storm and im interested in the parameters you can display on yours as the info on this site is more vipec related.

mail me on marcstav at sky dot com if you can help

thanks

Go to advanced search