another day and we are getting somewhere I had to download a HyperTerminal emulator! (now I'm a mech engineer!) There are loads on the interweb, but plenty are loaded with spam etc there are 2 that seem trustworthy PUtty and the one I used Tera Term I connected the 5v analogues to the 5v supply and ...

another day and we are getting somewhere I had to download a HyperTerminal emulator! (now I'm a mech engineer!) There are loads on the interweb, but plenty are loaded with spam etc there are 2 that seem trustworthy PUtty and the one I used Tera Term then i connected the 5v analogues to the 5v supply...

nearly the same problem I have, (mine says 57V) My computers running Vista so I don't have hyperterminal!
So RaceTech what are the options to calibrate the DL1 without hyperterminal?

I've wired up a temp sensor with a 1K pull up resistor According to my multimeter I have 3.8 volts across analogue 1 to earth Live monitor lite says the value is 57.8 I've swapped it to analogue 2 and the reading moves with it guessing i have a configuration issue, but really not sure lost 8 hours o...

dropped the analogue signal to channel 2 and getting the same reading 57.9. Channel 1 has gone back to a small background figure

well the resistance across the sensor is 53Kohms the voltage across the back of the DL1 with a 1K pull up is 4.82v so both indicate approximately 14 degrees - which match the water temp yet the live monitor on the DL1 says 57.92v and the value on the Dash 2 says 1273 So Ive proved my wiring is corre...

At work at the moment so dont have the answers around me Ive used a spreadsheet that calculates the volts to actual readings, its worked for the water temp, fuel gauge, and oil pressure so far. Ive input these values into the auto calculate section for setting up sensors in dash2 configuration runni...

Ive connected up an oil temp sensor. I have and checked the resistance values against the temperature and its very close to the manufacturers data I've wired it into analogue 1 on the DL1 and used a 1K pull up resistor running the light monitor on the DL1 im seeing a reading of about 57 on channel 1...

Cheers Mr support Man
I havent had time to look at this as the sprint season has started
My car is on display at Stoneleigh if you are ther this year (its where I bought the kit of you last year.
Any chance we can hook up on the saturday afternoon?

I ran out of patience and bought another sensor! I had to MOT it in january and needed some mileage on the dash

Hi Dave I have v7 for the dash 2, but as I can't send to the DL1 then I don't think I can update the DL1 either. The memory card is fine and the DL1 logs to it and I can read the log from the card to my laptop. Also when I connect the DL1 to the Dash2 all the lights on the DL1 stay on! I am a comple...

The live monitoring works so I definitely have coms from the DL1 to the laptop, but I just cant see how I can send a new configuration (V6 software)

I need to change my DL1 set up so my Dash 2 can trigger the DL1. However after over an hour I have not managed to get my laptop to talk to the DL1, I can open the software and change the setup, but cant connect or send to the DL1, I have saved it to the flash card and put the flash card in the DL1 b...

Cheers, its a simple thing to try, but due to the various instalations im aware of with the same problem in suprised it will work.
Not sure about the hz filter, where do i find that in the set up
Cheers WS

Its a singal wire from the ecu which sits on the tunnel to the dash which is just above it. It's all of 200mm long. There are now 7 people who all have the same problem regardless of there engine, ecu or configuration, this must be a race technology problem