Search found 79 matches

by DMKMM
Wed Aug 14, 2013 2:46 pm
Forum: General software support
Topic: a count variable
Replies: 8
Views: 14317

Thank you sir!
by DMKMM
Wed Aug 14, 2013 12:42 pm
Forum: General software support
Topic: a count variable
Replies: 8
Views: 14317

Wish it was that simple... I’m all corporate and junk, I’ll have to get a PO, start and eREQ, have a bunch of meetings.... ect.

Also I’m in the USA, I assume Al can take care of this for us?
by DMKMM
Wed Aug 14, 2013 12:13 pm
Forum: General software support
Topic: a count variable
Replies: 8
Views: 14317

I see that i have the serial and the analogue upgrades... Is this upgrade just a reflash thing or do i need to send the units back in?
by DMKMM
Tue Aug 13, 2013 5:00 pm
Forum: General software support
Topic: a count variable
Replies: 8
Views: 14317

oh sorry, DL1 MK3
by DMKMM
Mon Aug 12, 2013 5:17 pm
Forum: General software support
Topic: a count variable
Replies: 8
Views: 14317

a count variable

Hello, Is there any way to set up a count variable in analysis? I’m using a torque load cell to measure the breaking force of something... torque is the most important reading i want, but there is also an output for number of degrees of rotation. It is basically just an on/off switch that cycles e...
by DMKMM
Wed May 29, 2013 12:19 pm
Forum: Sensor-related questions
Topic: DL1 wont read bridge amp
Replies: 6
Views: 16468

problem has been sloved...

ground loop
by DMKMM
Wed May 22, 2013 4:52 pm
Forum: Sensor-related questions
Topic: DL1 wont read bridge amp
Replies: 6
Views: 16468

Are you getting 0v on the DL1 or are you seeing nothing at all? Make sure that the unit is configured to be logging the data and/or transmitting it on the serial port if you are monitoring it on a PC. Martin currently trying to just log onto card, and check in analysis, i checked that serial is on,...
by DMKMM
Wed May 22, 2013 4:23 pm
Forum: Sensor-related questions
Topic: DL1 wont read bridge amp
Replies: 6
Views: 16468

the range of the load cell is 500lbs @ +/-10vdc. when i stand on the load cell mulit meter it is saying 4.985vdc.. (im around 250lbs, stands to reason) i connect DL1 in parallel to meter, meter reads same, log data, load into analysis, analaysis shows 0 to .05mV , assume it should show same as meter...
by DMKMM
Tue May 21, 2013 7:18 pm
Forum: Sensor-related questions
Topic: DL1 wont read bridge amp
Replies: 6
Views: 16468

DL1 wont read bridge amp

trying to set up a brake pedal load sensor PCB# 1203-01A, with the PCB# 8162 bridge amp. The load cell works fine on the bench with a 12vdc supply, and reading the output with a mulitmeter. ie squeeze the load cell, the volts goes up on the multimeter... easy. I plug it into an analoge CH of a DL1, ...
by DMKMM
Thu Apr 04, 2013 12:20 pm
Forum: General support questions
Topic: bad analgoue readings
Replies: 7
Views: 11773

looks like interpolation was turned on... but channel 2 and 5 are still "messed up" they should look the same as the rest of them

Image
by DMKMM
Wed Apr 03, 2013 8:33 pm
Forum: General support questions
Topic: bad analgoue readings
Replies: 7
Views: 11773

uhh..

i dont think so? how does one check?
by DMKMM
Wed Apr 03, 2013 5:26 pm
Forum: General support questions
Topic: RT USA?
Replies: 1
Views: 6748

RT USA?

is RT USA ok? ive sent Al 3 emails and 2 voice mails over the past 5 days...

nothing
by DMKMM
Wed Apr 03, 2013 2:04 pm
Forum: General support questions
Topic: bad analgoue readings
Replies: 7
Views: 11773

all filtering is turned off
max rate of change is turned off, (non set, 0)
smoothed over: none set (0)
by DMKMM
Wed Apr 03, 2013 1:42 pm
Forum: General support questions
Topic: bad analgoue readings
Replies: 7
Views: 11773

bad analgoue readings

i was experienceing some problems using the analogue channels in our DL1. this is just a simple 5 -12vdc signal applied on... off, on, off, on, off applied to each of the 8 ananloge channels. this data should not look like this. reflash, new config in DL1 analysis reset to factor defaults no filteri...
by DMKMM
Mon Aug 06, 2012 3:30 pm
Forum: General support questions
Topic: DASH4 Pro, show text on value
Replies: 4
Views: 7884

true

i was just using "speed" off of the standard values (gps speed and accel)

i assume that dash only uses gps speed, dl does not combine with accel?

Go to advanced search