Search found 26 matches

by BBWRacing
Thu Sep 13, 2012 1:47 pm
Forum: General support questions
Topic: Gear Variable
Replies: 4
Views: 8950

In the Dash 2 you can setup the gear selector, via a sensor see
http://www.race-technology.com/wiki/ind ... alculation
by BBWRacing
Tue Aug 10, 2010 4:01 pm
Forum: General support questions
Topic: Lap times Dash 2
Replies: 14
Views: 18124

Support wrote:For the lap timing to work the DASH2 needs to be set up and configured to display the lap times.
Best starting point is this page in the Knowledge Base:
http://www.race-technology.com/wiki/ind ... /LapTiming


Thanks for that.
I think it's answered my question I was using lower case.
as been having problems getting the lap function to work.
by BBWRacing
Tue Aug 10, 2010 3:45 pm
Forum: General support questions
Topic: Can I have your data please?
Replies: 9
Views: 78471

BBWRacing - could you let me know what equations you are using for your Spa sensors? I cannot get sensible values out of mine... I wired mine up in parallel, and set the dash to volts. I then wrote down the values as the car warmed up, and at pressure changes. I then uses this info to make a matrix...
by BBWRacing
Tue Aug 10, 2010 9:45 am
Forum: General support questions
Topic: Can I have your data please?
Replies: 9
Views: 78471

I have
Brands Hatch
Rockingham
Snetterton
Mallory Park

All these are linked to a Emerald ECU so have all the ECU data, as well as oil pressure and temperature from a spa gauge.
by BBWRacing
Wed Jul 07, 2010 11:32 am
Forum: General software support
Topic: Dash 2 Lap times
Replies: 5
Views: 9868

Dash 2 Lap times

Can you have the lap time constantly displayed in the Odometer section
by BBWRacing
Tue Mar 31, 2009 2:23 pm
Forum: Sensor-related questions
Topic: Tyre Pressure & Tempreture Monitoring
Replies: 2
Views: 8826

All depends on how the sensors connect to the display.
They may talk via serial data maybe RS485 or 422. if so it will be difficult.
if they just output a change of voltage like most over sensors, its just a matter of tapping and mapping the voltage to the PSI, and connecting to a DL1 input.
by BBWRacing
Tue Mar 31, 2009 2:18 pm
Forum: Sensor-related questions
Topic: Tapping into SPA Design sensors/instruments
Replies: 1
Views: 7619

Re: Tapping into SPA Design sensors/instruments

Has anyone tapped into SPA Design supplied sensors/instruments? If so, how did you do it? The sensors have industrial type plugs so there's no easy option at that end, and at the SPA end there is a 12 way connector. There isn't even a lot of single insulated wire to tap into. You should be able to ...
by BBWRacing
Tue Mar 31, 2009 2:12 pm
Forum: Installation questions
Topic: DL1 Dash2 and Emerald ECU.
Replies: 34
Views: 107943

are you using the ECU interface, or going direct from emerald to the DL1? Is this the K3 or M3dk ECU?? Cheers Jim It's with the RT ECU interface, but you also have to use the PC cable that you get with the EMERALD, unless you convert the RT DB9 connector to use EMERALD pin out not stand serial ones...
by BBWRacing
Wed Mar 18, 2009 12:51 pm
Forum: Installation questions
Topic: DL1 Dash2 and Emerald ECU.
Replies: 34
Views: 107943

I've spoken to RT, and it look like you have to plug the ECT interface into the PC lead, not direct to the unit. Will try tonight and post my findings. Good news its all now working. Well if you have the DL1 and Dash2 connected to the Emerald via the Emerald PC cable. The Dash2 is still not working...
by BBWRacing
Tue Mar 17, 2009 12:42 pm
Forum: Installation questions
Topic: DL1 Dash2 and Emerald ECU.
Replies: 34
Views: 107943

I've spoken to RT, and it look like you have to plug the ECT interface into the PC lead, not direct to the unit.

Will try tonight and post my findings.
by BBWRacing
Wed Mar 11, 2009 7:11 pm
Forum: Installation questions
Topic: DL1 Dash2 and Emerald ECU.
Replies: 34
Views: 107943

BBWRacing wrote:Any news on anyone having this working.

Also can you log the ECU data on the DL1 and view on the software.

Thanks again
Leigh


Worked out how to set up the ECU varibles on the software, but still cant get the DL1 to log the ECU data or pass the data to the Dash2
by BBWRacing
Wed Mar 11, 2009 2:24 pm
Forum: Installation questions
Topic: DL1 Dash2 and Emerald ECU.
Replies: 34
Views: 107943

Any news on anyone having this working.

Also can you log the ECU data on the DL1 and view on the software.

Thanks again
Leigh
by BBWRacing
Thu Jul 17, 2008 4:39 pm
Forum: Installation questions
Topic: DL1 Dash2 and Emerald ECU.
Replies: 34
Views: 107943

Can you let us know what we need to do / get to get this all working together.

Thanks
Leigh
by BBWRacing
Thu Jul 17, 2008 4:34 pm
Forum: General software support
Topic: Dash 2 RPM input from a TVR / Landrover 14CUX ECU
Replies: 0
Views: 19017

Dash 2 RPM input from a TVR / Landrover 14CUX ECU

Is it posible to get a RPM reading into the Dash 2 from this ECU.

It does not seem to have a ECU output, the engine input comes from the - of the coil via a 6.8K resister

more information can be found here
http://www.britishv8.org/Articles/Rover-14CUX-EFI.htm

Thanks
Leigh
by BBWRacing
Thu Dec 20, 2007 1:46 pm
Forum: Sensor-related questions
Topic: Rover SD1 LT77 Gearbox Speed Transducer
Replies: 1
Views: 7183

Rover SD1 LT77 Gearbox Speed Transducer

Hi
This is a hall tranducer, can it be used as a speed source, for the Dash2.

Thanks
Leigh

Go to advanced search